300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

基于(火用)效率目标的环冷机余热回收系统操作参数优化

摘要：针对烧结环冷机余热回收利用率不高的难题，采用分析法建立了评价某钢铁厂烧结环冷机余热回收系统运行效率的效率模型。基于多孔介质模型、局部非热平衡方程、真实气体SRK方程建立环冷机内气固两相换热模型。通过CFD仿真模拟，探究料层高度、循环风机输入烟气温度、烧结矿底部入口风速三项可控环冷机运行工艺参数对系统效率的影响规律。结果表明，料层厚度在1～1.5 m区间每增加0.1 m，效率增加0.8%～1.1%；循环风温在100～140℃之间每增加10℃，效率增加1.4%～1.5%；烧结矿底部入口风速在0.9～1.9 m/s之间每增加0.1 m/s，效率降低0.18%～0.24%。在此基础上，基于工业运行数据建立效率正交试验优化模型，提高了该余热回收系统3.42%的效率。     

Precipitating spinel into precursor glass and its assistance in crystallization

The crystallization phenomena of spinel in CaO-MgO-Al₂O₃-SiO₂-Fe₂O₃ glass have received much attention due to the particular role in preparation of glass-ceramic materials, which represent an effective option to manage hazardous waste. In this study, both preliminary spinel and secondary spinel were precipitated in the precursor glass. The formation of these spinel was meticulously assessed by a combination of X-ray diffractometry and scanning electron microscopy. The structure of the microenvironment in the precursor glass was characterized by Raman spectrums. These advanced techniques highlight the potential for one-step crystallization of the glass. The investigation, which focused on one-step crystallization, demonstrated the growth of pyroxene on spinel accompanying a migration of chromium. The results also show the microstructure of the obtained glass-ceramic was very dependent on the heat-treat temperature. This study not only unambiguously reveals the precipitation mechanisms of spinel but also provides more documentation for one-step crystallization in the glass-ceramics field.     

基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。     

03Cr18NiMoN节镍双相不锈钢的热变形行为及热加工图

关键词：双相不锈钢； 流变曲线； 本构方程； 热加工图     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Tuning effect of silicon substitution on magnetic and high frequency electromagnetic properties of R2Fe17 and their composites

In this work, we report the tuning effect of the Si substitution on the magnetic and high frequency electromagnetic properties of R₂Fe₁₇ compounds and their paraffin composites. It is found that the introduction of Si can remarkably improve the magnetic and electromagnetic properties of the R₂Fe₁₇ compounds, making the R₂Fe_17–xSi_x-paraffin composites excellent microwave absorption materials (MAMs). By introducing the Si element, their saturation magnetizations decrease slightly, while much higher Curie temperatures are obtained. Furthermore, better impedance match is reached due to the decrease of the high-frequency permittivity ε′ by about 40%–50%, which finally enhances the performance of the microwave absorption. The peak frequency (f_RL) of the reflection loss (RL) curve moves toward high frequency domain and the qualified bandwidth (QB, RL ≤ ?10 dB) increases remarkably. The maximum QB of 3.3 GHz (12.0–15.3 GHz) is obtained for the Sm_1.5Y_0.5Fe₁₅Si₂-paraffin composite (d = 1.0 mm) and the maximum RL of ?53.6 dB is achieved for Nd₂Fe₁₅Si₂-paraffin composite (d = 2.2 mm), both surpassing most of the reported MAMs. Additionally, a distinguished dielectric microwave absorption peak is observed, which further increases the QB in these composites.     

On keys' meanings and modes: the impact of different key solutions on children's efficiency using a mobile phone

The present study investigates the impact of different key solutions of mobile phones on users' effectiveness and efficiency using the devices. In the first experiment, 36 children (9 - 14 years) and in the second experiment 45 young adults (19 - 33 years) completed four common phone tasks twice consecutively on three simulated phones that had identical menus, but different key solutions. An approach was undertaken to quantify the complexity of keys in three models, incorporating different factors contributing to the keys' complexity (number of key options, number of modes and number of modes with a semantically dissimilar meaning), in order to predict users' performance decrements. As a further main factor, the degree of the users' locus of control (LOC) was measured and interactions with performance outcomes were studied. As dependent measures, the number of inefficient keystrokes, the number of tasks solved and the processing time were determined. Results showed a significant effect of control key solutions on users' efficiency and effectiveness for both children and young adults. Moreover, children's LOC values significantly interacted with performance: children with low LOC values showed the lowest performance and no learnability, especially when using keys with a high complexity. From the three factors contributing to the complexity of keys, keys exerting different functions with semantically inconsistent meanings had the worst effect on performance. It is concluded that in mobile user interface design keys with semantically inconsistent meanings should be generally avoided.     

Incoloy825材料在加氢裂化装置高压空冷器上的应用

对Incoloy825材料的焊接和抗腐蚀性能,以及在加氢裂化装置高压空冷器上的应用中应注意的问题进行了探讨.对此种空冷器在制造中如何解决异种钢焊接的难题,在清洗和水压试验中如何避免腐蚀等提出了建议.